
Types of Hammers and Their Uses: Machinist, Sledge, Claw, Rubber and Chipping
November 16, 2026
The 5 main types of hammers explained: machinist, sledge, claw, rubber and chipping, with uses, sizes and handle options. APT hammers from Safinat, Dubai.
The main types of hammers used on sites and in workshops are the machinist hammer for metalwork, the sledge hammer for demolition and heavy driving, the claw hammer for driving and pulling nails, the rubber hammer for striking without marking the surface, and the chipping hammer for cleaning welds. Each one has a different head shape, weight and handle, and using the wrong one damages the work, the tool or your hands. This guide explains what each hammer is for, which sizes to buy, and how to choose between wooden and fiber handles. All the hammers shown are from the APT range stocked by Safinat Group in Dubai.
Why the type of hammer matters
A hammer looks like the simplest tool in the box, but the head is designed around one job. A claw hammer face is hardened to drive nails, not to strike a cold chisel. A sledge hammer delivers force that would shatter a tile. A rubber hammer protects a finished surface that a steel face would dent. Choosing by job, then by weight, then by handle is the quickest way to get the right hammer the first time.
1. Machinist hammer
The machinist hammer, often written as mechanist hammer or called an engineer's hammer, has a flat square striking face on one side and a wedge-shaped cross peen on the other. The face drives punches and chisels, and the peen is used to start small pins, shape metal and work in tight corners.
Best for: workshops, fabrication, vehicle repair and general metalwork. Striking punches and cold chisels, riveting, bending and straightening metal parts.
Sizes: the APT machinist hammer with black head comes in 300 gram, 500 gram and 800 gram head weights. Choose 300 g for light bench work, 500 g as the all-round workshop size and 800 g for heavier striking.
Tip: strike squarely with the face. A glancing blow can chip the edge of the head or the tool you are striking.
2. Sledge hammer with fiber handle
A sledge hammer has a heavy double-faced steel head built to deliver maximum force. It is the hammer for breaking concrete and masonry, driving stakes and wedges, and heavy demolition. The shorter, lighter versions are often called club hammers or lump hammers and are used one-handed with a chisel or bolster.
Best for: demolition, landscaping, site work, breaking block and concrete, driving stakes and ground pins.
Sizes: the APT double face sledge hammer with fiber handle is available in 2 lb, 3 lb, 4 lb, 6 lb and 8 lb. Use 2 lb to 4 lb for one-handed chisel work and light breaking, and 6 lb to 8 lb for two-handed demolition.
Why a fiber handle: a fiberglass handle absorbs more shock than steel, does not swell, shrink or rot in heat and humidity, and is far less likely to snap on a missed blow. For a tool that is swung hard all day on UAE sites, that is the main reason trade buyers choose fiber over wood.
3. Claw hammer: wooden handle and fiber handle
The claw hammer is the carpenter's hammer. One side of the head is a flat face for driving nails, and the other is a curved, split claw for pulling them out. It is the most common hammer in any toolbox, used for carpentry, framing, formwork, shuttering and general repairs.
Best for: driving and pulling nails, timber framing, formwork, pallets and crates, household and maintenance work.
Size: 16 oz is the standard general-purpose weight. It is heavy enough to drive common nails and light enough to use all day.
Wooden handle claw hammer
The APT 16 oz claw hammer with wooden handle is the traditional choice. Wood feels comfortable, dampens vibration naturally, and is the more economical option. It suits carpenters and general users, and it is the usual pick when buying in quantity for a crew.
Fiber handle claw hammer
The APT 16 oz claw hammer with fiber handle has a fiberglass core with a moulded non-slip grip. It is stronger when levering out large nails, is not affected by moisture, and the grip stays secure with sweaty or gloved hands. It suits site work and heavy daily use.
Tip: when pulling nails, put a block of wood under the head. It protects the surface and gives more leverage.
4. Rubber hammer (rubber mallet)
A rubber hammer, also called a rubber mallet, has a solid rubber head that delivers a firm blow without denting, cracking or marking the surface. It is used wherever a steel face would cause damage.
Best for: tapping floor and wall tiles into place, setting pavers and interlock, assembling furniture and joinery, fitting panels and aluminium sections, and closing paint tins.
Sizes: the APT rubber hammer with wooden handle comes in 12 oz, 16 oz and 24 oz. Use 12 oz or 16 oz for tiling and furniture assembly, and 24 oz for pavers and heavier fitting work.
Tip: on light-coloured tiles and stone, wipe the head clean before use so it does not leave marks.
5. Chipping hammer
A chipping hammer is the welder's hammer. The head has a pointed end and a flat chisel end, and it is used to knock slag off a weld bead after arc welding. The point clears slag from corners and the root of the weld, and the chisel edge cleans the flat run. Many have a spring-coil handle that absorbs shock and stays cool to hold.
Best for: removing welding slag and spatter, chipping off scale, rust and old paint before repainting, and general weld cleaning in fabrication shops.
Tip: always wear safety glasses or a face shield when chipping. Hot slag breaks off in sharp fragments. Follow up with a wire brush before the next weld pass.
Do not confuse this hand tool with the electric demolition or chipping hammer used for breaking concrete and removing tiles. That is a power tool, and you will find it under power tools.
Quick guide: which hammer for which job
- Driving or pulling nails: claw hammer, 16 oz.
- Striking punches and chisels, metalwork: machinist hammer, 300 g to 800 g.
- Breaking concrete and block, driving stakes: sledge hammer, 2 lb to 8 lb.
- Tiles, pavers and furniture assembly: rubber hammer, 12 oz to 24 oz.
- Cleaning welds, slag and scale: chipping hammer.
Wooden handle or fiber handle?
- Wooden handle: comfortable, naturally shock-absorbing, lower cost and easy to replace. It can dry out and loosen over time, so check that the head is tight.
- Fiber handle: stronger, resistant to moisture and heat, with a non-slip grip. It costs a little more and lasts longer under heavy use.
For occasional and workshop use, wood is a sound choice. For daily site work, demolition and outdoor storage, fiber is worth the difference.
Hammer safety and care
- Check that the head is tight on the handle before every use.
- Never use a hammer with a cracked handle or a chipped or mushroomed face.
- Do not strike one hammer with another, and do not use a claw hammer on hardened steel.
- Wear eye protection when striking metal, masonry or weld slag.
- Wipe the hammer clean after use and store it dry.
Where to buy hammers in Dubai
Safinat Group has supplied hardware and tools to UAE trade customers since 1990. The APT range of machinist, sledge, claw and rubber hammers is listed in our hand tools category, alongside other hand tool brands. There is no minimum order quantity, and delivery is guaranteed within 48 hours anywhere in the UAE. Contractors, workshops and retailers can also see our wholesale hardware supply in Dubai page for trade terms and export.
For sizes, availability and bulk pricing, call or WhatsApp +971 50 899 5435.
FAQ: types of hammers
What are the main types of hammers?
The five most used types are the claw hammer, machinist hammer, sledge hammer, rubber hammer and chipping hammer. Between them they cover carpentry, metalwork, demolition, tiling and welding.
What is a machinist hammer used for?
It is used in metalwork to strike punches and chisels, set rivets and shape metal. The cross peen on the back of the head is for starting pins and working in tight spaces.
What size sledge hammer do I need?
For one-handed work with a chisel, choose 2 lb to 4 lb. For breaking concrete and block with two hands, choose 6 lb or 8 lb.
Which is better, a wooden or fiber handle claw hammer?
Both drive nails equally well. A wooden handle is economical and comfortable. A fiber handle is stronger, handles moisture better and has a more secure grip, so it suits heavy site use.
What is the difference between a rubber hammer and a rubber mallet?
They are the same tool. Both names describe a hammer with a solid rubber head used to strike without marking the surface.
What is a chipping hammer used for?
A chipping hammer removes slag from welds after arc welding, and chips off spatter, scale and rust. It has a pointed end and a chisel end.
Where can I buy APT hammers in Dubai?
Safinat Group stocks APT hammers in Dubai with no minimum order and 48-hour delivery across the UAE. Call or WhatsApp +971 50 899 5435 for a quote.
